{"id":11027,"date":"2026-11-21T15:30:42","date_gmt":"2026-11-21T07:30:42","guid":{"rendered":"https:\/\/meettfit.com\/?p=11027"},"modified":"2026-11-21T14:18:57","modified_gmt":"2026-11-21T06:18:57","slug":"is-retesting-required-after-localized-repairs-to-esd-flooring-2","status":"publish","type":"post","link":"https:\/\/meettfit.com\/id\/blog-lantai-pvc\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/","title":{"rendered":"Apakah Diperlukan Pengujian Ulang Setelah Perbaikan Terbatas pada Lantai ESD?"},"content":{"rendered":"<p><strong>Electrical retesting is recommended after localized repairs that may affect the conductive surface or grounding path. ANSI\/ESD S20.20-2021 requires a compliance verification plan. Your repair type and site ESD program set the test scope.<\/strong><\/p>\n<p>I am a QC specialist at an ESD vinyl flooring manufacturer, and I check flooring quality every day. A small repair can look perfect and still change how the floor carries charge to ground. This matters most in electronics assembly, cleanrooms, aerospace, and data centers, where one weak spot in the grounding path can raise ESD risk for sensitive parts.<\/p>\n<p>The standard does not name &quot;small tile repair&quot; as a separate event with its own test rule. It asks you to verify that your ESD controls work, and it expects records. Your site&#8217;s ESD program or customer specification may require a retest after any repair. So I treat repairs that touch the electrical path as changes that need verification, and I size the test to the repair.<\/p>\n<h2>What Counts as a Localized ESD Flooring Repair?<\/h2>\n<p><strong>A localized repair is a small fix that touches the floor surface, the conductive layers below it, or the grounding path. Examples are replacing a few ESD vinyl tiles, patching a resin floor, and repairing copper strips or ground points.<\/strong><\/p>\n<p>Repair size does not set the risk. The risk depends on whether the repair touches the electrical path. A one-tile replacement that disturbs a copper strip matters more than a larger patch that stays on the surface. I sort repairs by what they touch, because each type needs a different test focus.<\/p>\n<h3>Common Repair Types and What to Check<\/h3>\n<table>\n<thead>\n<tr>\n<th>Repair Type<\/th>\n<th>What It Touches<\/th>\n<th>Apa yang Harus Diperiksa<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Replacing ESD vinyl tiles<\/td>\n<td>Tile, adhesive, conductive layer<\/td>\n<td>Adhesive type, bonding, contact with the conductive layer<\/td>\n<\/tr>\n<tr>\n<td>Patching epoxy, polyurethane, or ESD self-leveling floor<\/td>\n<td>Conductive primer and top layer<\/td>\n<td>Mixing, thickness, full cure<\/td>\n<\/tr>\n<tr>\n<td>Repairing copper foil or strip<\/td>\n<td>Grounding network<\/td>\n<td>Continuity along the strip<\/td>\n<\/tr>\n<tr>\n<td>Replacing a ground point<\/td>\n<td>Link to building ground<\/td>\n<td>Connection quality<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Why Do Repairs Affect ESD Flooring Performance?<\/h2>\n<p><strong>Repairs add new materials and can cut or cover parts of the grounding path. An unapproved adhesive, a broken copper strip, or a poorly cured patch can raise resistance and change test results.<\/strong><\/p>\n<p>ESD floor systems are not all built the same way. An ESD vinyl tile system may use a conductive adhesive and a copper grounding network. A resin system may use a conductive primer, a conductive topcoat, and copper strips. The details change from one product to the next, so check the build-up of your own floor before you plan a repair. In every system, the floor works as a chain: surface, conductive layers, and ground connection. A repair changes that chain at one point. If that link is weak, the area can lose its path to ground.<\/p>\n<h3>Main Causes of Electrical Problems After Repair<\/h3>\n<table>\n<thead>\n<tr>\n<th>Karena<\/th>\n<th>Apa yang Bisa Terjadi<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Adhesive or primer not approved for the system<\/td>\n<td>May interfere with continuity between the floor and its grounding parts<\/td>\n<\/tr>\n<tr>\n<td>Cut or covered copper strip<\/td>\n<td>Part of the floor may lose its path to ground<\/td>\n<\/tr>\n<tr>\n<td>Dirt, residue, or an aged surface on old floor<\/td>\n<td>Readings may differ between old and new areas<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><img decoding=\"async\" src=\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-2.png&quot;\" alt=\"ESD flooring layers with conductive adhesive and copper strip\" \/><\/p>\n<h2>What Do ESD Standards Say About Post-Repair Testing?<\/h2>\n<p><strong>ANSI\/ESD S20.20 requires a compliance verification plan. ESD TR53 explains how to verify and troubleshoot. ANSI\/ESD STM7.1 and IEC 61340-4-1 define how to test floor resistance. None of them list every small repair as a mandatory retest.<\/strong><\/p>\n<h3>What Each Document Does<\/h3>\n<table>\n<thead>\n<tr>\n<th>Dokumen<\/th>\n<th>Jenis<\/th>\n<th>Role for Floor Repairs<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>ANSI\/ESD S20.20-2021<\/td>\n<td>Standar<\/td>\n<td>Requires an ESD control program and a compliance verification plan<\/td>\n<\/tr>\n<tr>\n<td>ANSI\/ESD TR53-01-22<\/td>\n<td>Technical report<\/td>\n<td>Gives compliance verification procedures and troubleshooting guidance<\/td>\n<\/tr>\n<tr>\n<td>ANSI\/ESD STM7.1<\/td>\n<td>Metode pengujian<\/td>\n<td>Defines floor resistance measurement, including acceptance testing after installation<\/td>\n<\/tr>\n<tr>\n<td>IEC 61340-4-1:2003+A1:2015<\/td>\n<td>International test method<\/td>\n<td>Technically equivalent to ANSI\/ESD STM7.1<\/td>\n<\/tr>\n<tr>\n<td>IEC 61340-5-1<\/td>\n<td>Standar<\/td>\n<td>General ESD protection requirements<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3>Requirement, Recommendation, and Site Rules<\/h3>\n<table>\n<thead>\n<tr>\n<th>Tingkat<\/th>\n<th>Arti<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Standard requirement<\/td>\n<td>Keep a verification plan and follow it<\/td>\n<\/tr>\n<tr>\n<td>Technical recommendation<\/td>\n<td>Test after repairs that may affect the conductive surface or grounding path<\/td>\n<\/tr>\n<tr>\n<td>Site or customer rule<\/td>\n<td>Your program or customer may require a retest after any repair<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Check your own ESD control program and customer contracts. They often set stricter rules than the standard. Standards are revised from time to time, so state the edition you test against in every report.<\/p>\n<h2>When Should You Retest ESD Flooring After a Repair?<\/h2>\n<p><strong>For repairs that use adhesives, primers, or resin materials, test after the cure time on the manufacturer&#8217;s technical data sheet. Testing before full cure can give readings that differ from the final result.<\/strong><\/p>\n<p>A common mistake is testing the day after the repair because the area must reopen. A high reading at that point may not mean the repair failed. Adhesives, primers, and resin patches reach their final electrical behavior only after full cure. If the team tears out the patch based on an early reading, they waste time and material. Room temperature and humidity can change cure time, so always follow the data sheet for your product.<\/p>\n<p>Some repairs do not involve curing materials. For example, replacing a copper strip or repairing a ground connection has no cure window. For these, complete the required electrical checks after installation and before you return the area to service.<\/p>\n<h3>Cure Planning<\/h3>\n<table>\n<thead>\n<tr>\n<th>Perbaikan<\/th>\n<th>What to Follow<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Perekat konduktif<\/td>\n<td>Cure time on the data sheet<\/td>\n<\/tr>\n<tr>\n<td>Epoxy or polyurethane patch<\/td>\n<td>Full cure time, not touch-dry time<\/td>\n<\/tr>\n<tr>\n<td>ESD self-leveling floor<\/td>\n<td>Supplier guidance on cure and moisture<\/td>\n<\/tr>\n<tr>\n<td>Copper strip or ground point repair<\/td>\n<td>No cure window. Test after installation<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Write the cure end time on the repair work order. The tester then knows when to start.<\/p>\n<h2>Which Areas Should You Test After a Localized Repair?<\/h2>\n<p><strong>Test the repaired area and its boundary using the electrode layout in ANSI\/ESD STM7.1. Check the grounding connection too. Expand the test area if the repair affects a grounding connection or conductive network.<\/strong><\/p>\n<p>The repair boundary needs close attention, because changes in bonding and conductive contact can affect electrical performance. Follow the electrode placement rules in STM7.1. For resistance-to-ground measurements, keep the electrode off the seam. For point-to-point measurements, place the electrodes on opposite sides of a seam when the test layout requires it. You can add diagnostic readings if you suspect a problem. Label them as diagnostic in your record.<\/p>\n<h3>Test Scope Guide<\/h3>\n<table>\n<thead>\n<tr>\n<th>Lokasi<\/th>\n<th>Jenis Tes<\/th>\n<th>Catatan<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Repaired area<\/td>\n<td>Point-to-point and resistance-to-ground testing<\/td>\n<td>Follow STM7.1 electrode placement<\/td>\n<\/tr>\n<tr>\n<td>Repair boundary<\/td>\n<td>Point-to-point testing where applicable<\/td>\n<td>Place electrodes on opposite sides of the seam when required<\/td>\n<\/tr>\n<tr>\n<td>Grounding connection<\/td>\n<td>Grounding continuity inspection<\/td>\n<td>This is a different check from surface resistance testing<\/td>\n<\/tr>\n<tr>\n<td>Nearby original floor<\/td>\n<td>Baseline readings<\/td>\n<td>Compare with the surrounding floor<\/td>\n<\/tr>\n<tr>\n<td>Wider grounding network<\/td>\n<td>Expanded resistance testing<\/td>\n<td>Needed when the repair may affect other areas<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Do not set the scope by room. Grounding networks do not always follow room lines. Base the scope on the actual grounding layout and cover every area the repair could affect.<\/p>\n<p>Some repair areas are too small for the electrode spacing that the method requires. In that case, a qualified tester should set the test plan based on the floor system and your ESD program. Report the readings as measured with an adjusted layout. Do not call them formal STM7.1 results unless the layout meets the method.<\/p>\n<h2>How Do You Retest ESD Flooring?<\/h2>\n<p><strong>Inspect the repair, use a calibrated surface resistance meter with 5-pound electrodes, measure point-to-point and resistance-to-ground, record the test voltage, and log temperature and humidity.<\/strong><\/p>\n<h3>Step 1: Inspect the Repair<\/h3>\n<p>Check for flush seams, firm bonding, no air pockets, and no residue over grounding parts.<\/p>\n<h3>Step 2: Prepare the Equipment and Electrodes<\/h3>\n<p>Use a calibrated surface resistance meter with cylindrical 5-pound (about 2.27 kg) electrodes. Each electrode should have a diameter of 2.5 inches (63.5 mm). The conductive contact material must meet the Shore A hardness requirement in ANSI\/ESD STM7.1. Check the meter calibration date before you start.<\/p>\n<p>The two measurements use different connections:<\/p>\n<table>\n<thead>\n<tr>\n<th>Pengukuran<\/th>\n<th>Koneksi<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Point-to-point<\/td>\n<td>Two surface electrodes placed on the floor at the spacing the method requires<\/td>\n<\/tr>\n<tr>\n<td>Resistance to ground<\/td>\n<td>One surface electrode on the floor, with the meter connected to a ground reference<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Published guidance often shows an electrode spacing of about 36 inches (0.9 m) for both measurements. Confirm the spacing and ground reference location in the edition of STM7.1 you use.<\/p>\n<p>For post-repair acceptance testing, use the applicable ANSI\/ESD STM7.1 procedures. For routine ESD compliance verification, follow the flooring procedure in ESD TR53. These methods serve related but different purposes and are not interchangeable.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-3.png&quot;\" alt=\"Point-to-point and resistance-to-ground electrode layouts on an ESD floor\" \/><\/p>\n<h3>Step 3: Take the Electrical Measurements<\/h3>\n<p>Select the test voltage according to the test procedure and the meter manufacturer&#8217;s instructions. Allow the reading to stabilize before you record it. Record the actual test voltage with each result.<\/p>\n<table>\n<thead>\n<tr>\n<th>Pengukuran<\/th>\n<th>Apa yang Ditunjukkan<\/th>\n<th>Required Limit<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Resistansi titik ke titik<\/td>\n<td>Resistance between two points on the floor surface<\/td>\n<td>Less than 1.0 x 10^9 ohms<\/td>\n<\/tr>\n<tr>\n<td>Resistance to ground (point-to-groundable point)<\/td>\n<td>Resistance between the floor surface and a groundable point<\/td>\n<td>Less than 1.0 x 10^9 ohms<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>These limits come from ANSI\/ESD S20.20-2021 for ESD flooring. Check the current edition before you set your acceptance criteria. Your customer or program may set tighter limits.<\/p>\n<p>ANSI\/ESD STM7.1 uses the term Resistance to Ground (RTG). ANSI\/ESD S20.20-2021 Table 3 lists the matching flooring requirement as point-to-groundable point resistance. Write the test method and the measurement name clearly in your report.<\/p>\n<h3>Step 4: Record Environmental Conditions<\/h3>\n<p>Write down temperature and relative humidity at the time of the test. Humidity affects ESD floor readings, and a result without these numbers is hard to defend.<\/p>\n<h2>What Should You Do If ESD Flooring Fails the Retest?<\/h2>\n<p><strong>Do not remove the repair at once. First check the test conditions, the instrument, surface cleanliness, cure state, adhesive type, and grounding connection. Fix the cause, then retest with the same method.<\/strong><\/p>\n<p>A failed first reading does not always mean a bad repair. Dirt, residue, an early test, or a wrong test setup can all give a high number. Rule out these simple causes first. If the readings still fail, look at the materials and the ground path. Do not treat the area as verified until it meets your project limits.<\/p>\n<h3>Troubleshooting Checklist<\/h3>\n<table>\n<thead>\n<tr>\n<th>Periksa<\/th>\n<th>Apa yang Harus Diperhatikan<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Kondisi pengujian<\/td>\n<td>Meter calibration, electrode condition, voltage, temperature, humidity<\/td>\n<\/tr>\n<tr>\n<td>Kondisi permukaan<\/td>\n<td>Dirt, insulating residue, or contamination<\/td>\n<\/tr>\n<tr>\n<td>Cure state<\/td>\n<td>Full cure time reached per the data sheet<\/td>\n<\/tr>\n<tr>\n<td>Kompatibilitas perekat<\/td>\n<td>The specified ESD adhesive was used<\/td>\n<\/tr>\n<tr>\n<td>Grounding connection<\/td>\n<td>Copper strip, ground point, and connections<\/td>\n<\/tr>\n<tr>\n<td>Conductive layer<\/td>\n<td>Damage or breaks in the conductive layer<\/td>\n<\/tr>\n<tr>\n<td>Material differences<\/td>\n<td>Batch or age difference between the new and old floor<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>After you fix the cause, repeat the test with the same method and electrode layout. Record both the failed and the passed results.<\/p>\n<h2>What Records Should You Keep After an ESD Flooring Repair?<\/h2>\n<p><strong>Keep the damage description and location, materials used, test method, test voltage, actual readings, environmental conditions, and the meter calibration certificate.<\/strong><\/p>\n<p>Keep the repair and test records with your ESD control program documents so auditors can review them later. Link each record to a floor map that marks the repair location. Over time, the map shows which areas need repair most often. That helps you decide when to change the floor build for that zone, such as the material, the cleaning method, or the traffic plan.<\/p>\n<h3>Repair Record Contents<\/h3>\n<table>\n<thead>\n<tr>\n<th>Rekor<\/th>\n<th>Apa Saja yang Harus Disertakan<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Damage report<\/td>\n<td>What failed, where, and when<\/td>\n<\/tr>\n<tr>\n<td>Bahan<\/td>\n<td>Data sheets for adhesive, tiles, primer, or resin<\/td>\n<\/tr>\n<tr>\n<td>Cure log<\/td>\n<td>Start time, cure time, and test start time<\/td>\n<\/tr>\n<tr>\n<td>Test date and method<\/td>\n<td>Date, standard edition, and whether STM7.1 or TR53 was used<\/td>\n<\/tr>\n<tr>\n<td>Test voltage<\/td>\n<td>Voltage used for each reading<\/td>\n<\/tr>\n<tr>\n<td>Electrode layout<\/td>\n<td>Diagram of electrode positions<\/td>\n<\/tr>\n<tr>\n<td>Ground reference<\/td>\n<td>Location of the ground point used<\/td>\n<\/tr>\n<tr>\n<td>Actual readings<\/td>\n<td>Measured values, not only pass or fail<\/td>\n<\/tr>\n<tr>\n<td>Lingkungan<\/td>\n<td>Suhu dan kelembapan relatif<\/td>\n<\/tr>\n<tr>\n<td>Peralatan<\/td>\n<td>Meter and electrode details with calibration certificate<\/td>\n<\/tr>\n<tr>\n<td>Failures and fixes<\/td>\n<td>Any failed readings, cause found, and corrective action<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><img decoding=\"async\" src=\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-4.png&quot;\" alt=\"ESD flooring repair record with test points and measurements\" \/><\/p>\n<h2>What Is the ESD Flooring Repair Retest Checklist?<\/h2>\n<p><strong>Use approved repair materials, wait for full cure where it applies, test with the prescribed method, compare results with your limits, and archive every record.<\/strong><\/p>\n<table>\n<thead>\n<tr>\n<th>Langkah<\/th>\n<th>Tindakan<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>1<\/td>\n<td>Use the adhesive and materials specified by the flooring manufacturer<\/td>\n<\/tr>\n<tr>\n<td>2<\/td>\n<td>Wait for the full cure time on the data sheet, if the repair uses curing materials<\/td>\n<\/tr>\n<tr>\n<td>3<\/td>\n<td>Test with a calibrated meter and STM7.1 electrodes, using the right layout<\/td>\n<\/tr>\n<tr>\n<td>4<\/td>\n<td>Record voltage, temperature, humidity, and actual readings<\/td>\n<\/tr>\n<tr>\n<td>5<\/td>\n<td>Investigate any failure before you reopen the area<\/td>\n<\/tr>\n<tr>\n<td>6<\/td>\n<td>Archive reports for the next audit<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Kesimpulan<\/h2>\n<p>A repair that may affect the conductive surface or grounding path should be tested before you treat the floor as verified. Follow the method and keep the records.<\/p>\n<p><strong>Need help choosing compatible ESD flooring repair materials or planning post-repair electrical testing? Send me a private message and tell me about your floor system.<\/strong><\/p>","protected":false},"excerpt":{"rendered":"<p>Electrical retesting is recommended after localized repairs that may affect the conductive surface or grounding path. ANSI\/ESD S20.20-2021 requires a compliance verification plan. Your repair type and site ESD program set the test scope. I am a QC specialist at an ESD vinyl flooring manufacturer, and I check flooring quality every day. A small repair&#8230;<\/p>","protected":false},"author":4,"featured_media":11010,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[21],"tags":[],"class_list":["post-11027","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-pvc-floor-blog"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v24.6 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR<\/title>\n<meta name=\"description\" content=\"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/meettfit.com\/id\/blog-lantai-pvc\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\" \/>\n<meta property=\"og:locale\" content=\"id_ID\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR\" \/>\n<meta property=\"og:description\" content=\"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/meettfit.com\/id\/blog-lantai-pvc\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\" \/>\n<meta property=\"og:site_name\" content=\"MF FLOOR\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/profile.php?id=100079773047357\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-21T07:30:42+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"Leo\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Ditulis oleh\" \/>\n\t<meta name=\"twitter:data1\" content=\"Leo\" \/>\n\t<meta name=\"twitter:label2\" content=\"Estimasi waktu membaca\" \/>\n\t<meta name=\"twitter:data2\" content=\"1 menit\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\"},\"author\":{\"name\":\"Leo\",\"@id\":\"https:\/\/meettfit.com\/#\/schema\/person\/ba93f0ead95f571b725acc83f6544fef\"},\"headline\":\"Is Retesting Required After Localized Repairs to ESD Flooring\",\"datePublished\":\"2026-11-21T07:30:42+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\"},\"wordCount\":2142,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/meettfit.com\/#organization\"},\"image\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png\",\"articleSection\":[\"Vinyl Flooring Insights\"],\"inLanguage\":\"id\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\",\"url\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\",\"name\":\"Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR\",\"isPartOf\":{\"@id\":\"https:\/\/meettfit.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png\",\"datePublished\":\"2026-11-21T07:30:42+00:00\",\"description\":\"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.\",\"breadcrumb\":{\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#breadcrumb\"},\"inLanguage\":\"id\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"id\",\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage\",\"url\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png\",\"contentUrl\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png\",\"width\":800,\"height\":600,\"caption\":\"PVC Flooring11 (1)\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/meettfit.com\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Is Retesting Required After Localized Repairs to ESD Flooring\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/meettfit.com\/#website\",\"url\":\"https:\/\/meettfit.com\/\",\"name\":\"MF FLOOR\",\"description\":\"fitness and sports floor China factory\",\"publisher\":{\"@id\":\"https:\/\/meettfit.com\/#organization\"},\"alternateName\":\"MF FLOOR\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/meettfit.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"id\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/meettfit.com\/#organization\",\"name\":\"MF FLOOR\",\"alternateName\":\"MF FLOOR\",\"url\":\"https:\/\/meettfit.com\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"id\",\"@id\":\"https:\/\/meettfit.com\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2025\/02\/cropped-icon.png\",\"contentUrl\":\"https:\/\/meettfit.com\/wp-content\/uploads\/2025\/02\/cropped-icon.png\",\"width\":512,\"height\":512,\"caption\":\"MF FLOOR\"},\"image\":{\"@id\":\"https:\/\/meettfit.com\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.facebook.com\/profile.php?id=100079773047357\"]},{\"@type\":\"Person\",\"@id\":\"https:\/\/meettfit.com\/#\/schema\/person\/ba93f0ead95f571b725acc83f6544fef\",\"name\":\"Leo\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"id\",\"@id\":\"https:\/\/meettfit.com\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/848b16970688cfb2f4cc64e85a2e2233183d3242ed0a21ffa4c859df339031f6?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/848b16970688cfb2f4cc64e85a2e2233183d3242ed0a21ffa4c859df339031f6?s=96&d=mm&r=g\",\"caption\":\"Leo\"},\"url\":\"https:\/\/meettfit.com\/id\/author\/1659230944qq-com\/\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR","description":"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/meettfit.com\/id\/blog-lantai-pvc\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/","og_locale":"id_ID","og_type":"article","og_title":"Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR","og_description":"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.","og_url":"https:\/\/meettfit.com\/id\/blog-lantai-pvc\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/","og_site_name":"MF FLOOR","article_publisher":"https:\/\/www.facebook.com\/profile.php?id=100079773047357","article_published_time":"2026-11-21T07:30:42+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png","type":"image\/png"}],"author":"Leo","twitter_card":"summary_large_image","twitter_misc":{"Ditulis oleh":"Leo","Estimasi waktu membaca":"1 menit"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#article","isPartOf":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/"},"author":{"name":"Leo","@id":"https:\/\/meettfit.com\/#\/schema\/person\/ba93f0ead95f571b725acc83f6544fef"},"headline":"Is Retesting Required After Localized Repairs to ESD Flooring","datePublished":"2026-11-21T07:30:42+00:00","mainEntityOfPage":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/"},"wordCount":2142,"commentCount":0,"publisher":{"@id":"https:\/\/meettfit.com\/#organization"},"image":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage"},"thumbnailUrl":"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png","articleSection":["Vinyl Flooring Insights"],"inLanguage":"id","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/","url":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/","name":"Is Retesting Required After Localized Repairs to ESD Flooring - MF FLOOR","isPartOf":{"@id":"https:\/\/meettfit.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage"},"image":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage"},"thumbnailUrl":"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png","datePublished":"2026-11-21T07:30:42+00:00","description":"Learn when ESD flooring needs retesting after repairs, which electrical tests to perform, and how to verify grounding and resistance.","breadcrumb":{"@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#breadcrumb"},"inLanguage":"id","potentialAction":[{"@type":"ReadAction","target":["https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/"]}]},{"@type":"ImageObject","inLanguage":"id","@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#primaryimage","url":"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png","contentUrl":"https:\/\/meettfit.com\/wp-content\/uploads\/2026\/11\/PVC-Flooring11-1.png","width":800,"height":600,"caption":"PVC Flooring11 (1)"},{"@type":"BreadcrumbList","@id":"https:\/\/meettfit.com\/pvc-floor-blog\/is-retesting-required-after-localized-repairs-to-esd-flooring-2\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/meettfit.com\/"},{"@type":"ListItem","position":2,"name":"Is Retesting Required After Localized Repairs to ESD Flooring"}]},{"@type":"WebSite","@id":"https:\/\/meettfit.com\/#website","url":"https:\/\/meettfit.com\/","name":"MF FLOOR","description":"fitness and sports floor China factory","publisher":{"@id":"https:\/\/meettfit.com\/#organization"},"alternateName":"MF FLOOR","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/meettfit.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"id"},{"@type":"Organization","@id":"https:\/\/meettfit.com\/#organization","name":"MF FLOOR","alternateName":"MF FLOOR","url":"https:\/\/meettfit.com\/","logo":{"@type":"ImageObject","inLanguage":"id","@id":"https:\/\/meettfit.com\/#\/schema\/logo\/image\/","url":"https:\/\/meettfit.com\/wp-content\/uploads\/2025\/02\/cropped-icon.png","contentUrl":"https:\/\/meettfit.com\/wp-content\/uploads\/2025\/02\/cropped-icon.png","width":512,"height":512,"caption":"MF FLOOR"},"image":{"@id":"https:\/\/meettfit.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/profile.php?id=100079773047357"]},{"@type":"Person","@id":"https:\/\/meettfit.com\/#\/schema\/person\/ba93f0ead95f571b725acc83f6544fef","name":"Leo","image":{"@type":"ImageObject","inLanguage":"id","@id":"https:\/\/meettfit.com\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/848b16970688cfb2f4cc64e85a2e2233183d3242ed0a21ffa4c859df339031f6?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/848b16970688cfb2f4cc64e85a2e2233183d3242ed0a21ffa4c859df339031f6?s=96&d=mm&r=g","caption":"Leo"},"url":"https:\/\/meettfit.com\/id\/author\/1659230944qq-com\/"}]}},"_links":{"self":[{"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/posts\/11027","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/comments?post=11027"}],"version-history":[{"count":1,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/posts\/11027\/revisions"}],"predecessor-version":[{"id":11029,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/posts\/11027\/revisions\/11029"}],"wp:attachment":[{"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/media?parent=11027"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/categories?post=11027"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/meettfit.com\/id\/wp-json\/wp\/v2\/tags?post=11027"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}